manualshive.com logo in svg

HP 5400R zl2 Series, Инструкция по установке и началу работы

Поделиться
Скачать
HP 5400R zl2 Series Скачать руководство пользователя страница 74

4-4

Replacing Components

Replacing Fan Trays

Repl

aci

ng Comp

one

nts

Replacing Fan Trays

When a fan fails the Fan Status LED on the management module blinks 
simultaneously with the switch Fault LED. In this case, the entire fan tray 
needs to be replaced. You cannot replace individual fans.

The fan tray is hot swappable. It can be removed and replaced without 
removing power from the switch. However, install the new fan tray 
immediately (after two minutes) after removing the old fan tray to avoid 
overheating and switch shutdown (after three minutes). The fan tray is 
provided with a hotswap controller on the backplane to control the fan power 
interface during insertion and removal.

Although these procedures show the 6-slot chassis, the procedures are the 
same for the 12-slot chassis. 

W A R N I N G

To avoid contact with spinning fans, if you are hot swapping out the 
fan tray assembly, pull the assembly out one-inch and allow the fans 
to stop rotating (approximately 20 seconds) before pulling it all the 
way out.

To replace a fan tray:

1.

Using either a flat-bladed or Torx T-10 screwdriver loosen the retaining 
screws holding the fan tray assembly and pull the fan tray assembly out.

2.

Install the new fan tray assembly and tighten the retaining screws.

 

Figure 4-3. 5406R zl2 Switch Fan Tray removal

Figure 4-4. 5406R zl2 Switch Fan Tray insertion

Retaining Screws

Handle

Retaining Screws

Handle

Содержание 5400R zl2 Series













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды