HP 3100 v2 Series Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 239

HP 3100 v2 Series Скачать руководство пользователя страница 84

77

By default, the system selects the load sharing criteria according to the packet type.

This command applies to only unicast packets, and can change the load sharing criteria for unicast
packets. Broadcast packets and multicast packets always use the default load sharing criteria.

The load sharing criteria that you configure will overwrite the previous criteria.

If unsupported load sharing criteria are configured, an error prompt will appear.

In system view, the switch supports the following load sharing criteria and combinations:

•

Load sharing criteria automatically determined based on the packet type.

•

Source IP address.

•

Destination IP address.

•

Source MAC address.

•

Destination MAC address.

•

Source IP address and destination IP address.

•

Source MAC address and destination MAC address.

Examples

# Configure the destination MAC address as the global link-aggregation load sharing criterion.

<Sysname> system-view

[Sysname] link-aggregation load-sharing mode destination-mac

link-aggregation mode

Syntax

link-aggregation mode dynamic

undo link-aggregation mode

View

Layer 2 aggregate interface view

Default level

2: System level

Parameters

None

Description

Use the

link-aggregation mode dynamic

command to configure an aggregation group to operate

in dynamic aggregation mode.

Use

undo link-aggregation mode

to restore the default setting.

By default, an aggregation group operates in static aggregation mode.

To change the aggregation mode of an aggregation group that contains member ports, remove all
the member ports from the aggregation group first.

Examples

# Configure the aggregation group corresponding to Bridge-Aggregation 1 to operate in dynamic
aggregation mode.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation mode dynamic

«
...
82
83
84
85
86
...
»

Содержание 3100 v2 Series
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды