HP 3100 v2 Series Скачать руководство пользователя страница 83

Страница: 83 / 239

lacp system-priority

Syntax

lacp

system-priority

system-priority

undo

lacp

system-priority

View

System view

Default level

2: System level

Parameters

system-priority

: Specifies the LACP priority of the local system, in the range of 0 to 65535. The

smaller the value, the higher the system LACP priority.

Description

Use

lacp

system

priority

to set the LACP priority of the local system.

Use

undo

lacp

system-priority

to restore the default setting.

By default, the system LACP priority is 32768.

Examples

# Set the system LACP priority to 64.

<Sysname> system-view

[Sysname] lacp system-priority 64

link-aggregation load-sharing mode

Syntax

link-aggregation load-sharing mode

{

destination-ip

destination-mac

source-ip

source-mac

} *

undo link-aggregation load-sharing mode

View

System view

Default level

2: System level

Parameters

destination-ip

: Performs load sharing in link aggregation groups based on destination IP address.

destination-mac

: Performs load sharing in link aggregation groups based on destination MAC

address.

source-ip

: Performs load sharing in link aggregation groups based on source IP address.

source-mac

: Performs load sharing in link aggregation groups based on source MAC address.

Description

Use

link-aggregation load-sharing mode

to configure the global link-aggregation load sharing

criteria.

Use

undo link-aggregation load-sharing mode

to restore the default setting.

Содержание 3100 v2 Series
















































































































































































































































Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды

HP 3100 v2 Series, Справочник по командам

Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды