HP 3100 v2 Series Скачать руководство пользователя страница 65

Страница: 65 / 239

[Sysname] interface ethernet 1/0/1

[Sysname-Ethernet1/0/1] mac-address max-mac-count 600

mac-address timer

Syntax

mac-address timer

{

aging seconds

no-aging

}

undo mac-address timer aging

View

System view

Default level

2: System level

Parameters

aging seconds

: Sets an aging timer (in seconds) for dynamic MAC address entries. The value is in

the range of 10 to 1000000 seconds.

no-aging

: Sets dynamic MAC address entries not to age.

Description

Use

mac-address timer

to configure the aging timer for dynamic MAC address entries.

Use

undo mac-address timer

to restore the default.

By default, the aging timer is 300 seconds.

Follow these guidelines to set the aging timer appropriately:

•

A long aging interval may cause the MAC address table to retain outdated entries and fail to
accommodate the latest network changes.

•

A short aging interval may result in removal of valid entries and unnecessary broadcasts that
may affect the performance of the switch.

Examples

# Set the aging timer for dynamic MAC address entries to 500 seconds.

<Sysname> system-view

[Sysname] mac-address timer aging 500

mac-flapping notification enable

Use

mac-flapping notification enable

to enable MAC address migration log notifying.

Use

undo mac-flapping notification enable

to disable the MAC address migration notifying.

Syntax

mac-flapping notification enable

undo mac-flapping notification enable

Default

MAC address migration log notifying is disabled.

Views

System view

Содержание 3100 v2 Series
















































































































































































































































Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды

HP 3100 v2 Series, Справочник по командам

Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды