manualshive.com logo in svg

HP 3100 v2 Series, Справочник по командам

Поделиться
Скачать
HP 3100 v2 Series Скачать руководство пользователя страница 38

31 

undo shutdown 

View 

Ethernet interface view, port group view 

Default level 

2: System level 

Parameters 

None 

Description 

 

 

CAUTION: 

After you shut down an Ethernet interface with this command, it cannot forward packets, even if it is
physically connected. 

 

Use 

shutdown 

to shut down an Ethernet interface. 

Use 

undo

 

shutdown 

to bring up an Ethernet interface. 

By default, an Ethernet interface is in up state. 

Examples 

# Shut down and then bring up Ethernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] shutdown 

[Sysname-Ethernet1/0/1] undo shutdown 

# Shut down all member ports in the port group named group1. 

<Sysname> system-view 

[Sysname] port-group manual group1 

[Sysname-port-group-manual-group1] shutdown 

speed 

Syntax 

speed

 {

 10 

|

 100 

|

 1000 

| 

auto

 } 

undo speed 

View 

Ethernet interface view 

Default level 

2: System level 

Parameters 

10

: Sets the interface speed to 10 Mbps.  

100

: Sets the interface speed to 100 Mbps.  

1000

: Sets the interface speed to 1000 Mbps.  

auto

: Enables the interface to negotiate a speed with its peer. 

Содержание 3100 v2 Series
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды