manualshive.com logo in svg

HP 3100 v2 Series, Справочник по командам

Поделиться
Скачать
HP 3100 v2 Series Скачать руководство пользователя страница 35

28 

mdi 

Syntax 

mdi 

{

 across 

|

 auto 

|

 normal 

}

 

undo mdi 

View 

Ethernet interface view 

Default level 

2: System level 

Parameters 

across

: Sets the MDI mode to across. In this mode, pins 1 and 2 of the port are receive pins, and 

pins 3 and 6 are transmit pins. 

auto

: Sets the MDI mode to auto. In this mode, the port negotiates pin roles with its peer. 

normal

: Sets the MDI mode to normal. In normal mode, pins 1 and 2 of the port are transmit pins, 

and pins 3 and 6 are receive pins. 

Description 

Use 

mdi 

to configure the MDI mode of a copper Ethernet interface. 

Use 

undo mdi 

to restore the default. 

By default, Ethernet interfaces operate in auto MDI mode. 

 

 

NOTE: 

This command is not applicable to fiber ports. 

 

Examples 

# Set Ethernet 1/0/1 to operate in across MDI mode. 

<Sysname> system-view 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] mdi across 

multicast-suppression 

multicast-suppression

 { 

ratio 

|

 kbps max-kbps

 } 

undo

 

multicast-suppression

 

View 

Ethernet interface view, port group view 

Default level 

2: System level 

Parameters 

ratio

: Sets the multicast suppression threshold as a percentage of the maximum interface rate, 

ranging from 1 to 100. The smaller the percentage, the less multicast traffic is allowed to pass 
through. 

kbps  max-kbps

: Specifies the maximum number of kilobits of multicast traffic that the Ethernet 

interface can forward per second.  

Содержание 3100 v2 Series
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды