HP 3100 v2 Series Скачать руководство пользователя страница 183

Страница: 183 / 239

176

Description

Use

display gvrp vlan-operation

to display information about dynamic VLAN operations on a port.

Examples

# Display information about dynamic VLAN operations on Ethernet 1/0/1.

<Sysname> display gvrp vlan-operation interface ethernet 1/0/1

Dynamic VLAN operations on port Ethernet1/0/1

Operations of creating VLAN : 2-100

Operations of deleting VLAN : none

Operations of adding VLAN to TRUNK : 2-100

Operations of deleting VLAN from TRUNK : none

garp timer hold

Syntax

garp timer hold

timer-value

undo garp timer hold

View

Ethernet interface view, Layer-2 aggregate interface view, port group view

Default level

2: System level

Parameters

timer-value

: Hold timer (in centiseconds), which must be a multiple of 5 and range from 10 (inclusive)

to half the Join timer (inclusive).

Description

Use

garp timer hold

to set the GARP Hold timer for an Ethernet port, Layer-2 aggregate interface,

or all ports in a port group.

Use

undo garp timer hold

to restore the default of the GARP Hold timer. This may fail if the default

is beyond the valid value range for the Hold timer.

By default, the Hold timer is 10 centiseconds.

Related commands:

display garp timer

and

garp timer join

Examples

# Set the GARP Hold timer to 15 centiseconds, assuming that the Join timer is 30 centiseconds.

<Sysname> system-view

[Sysname] interface ethernet 1/0/1

[Sysname-Ethernet1/0/1] garp timer hold 15

garp timer join

Syntax

garp timer join timer-value

undo garp timer join

Содержание 3100 v2 Series
















































































































































































































































Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды

HP 3100 v2 Series, Справочник по командам

Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды