manualshive.com logo in svg

HP 3100 v2 Series, Справочник по командам

Поделиться
Скачать
HP 3100 v2 Series Скачать руководство пользователя страница 177

 

170 

GVRP configuration commands 

display garp statistics 

Syntax 

display

 

garp statistics 

[ 

interface interface-list

 ] [ 

|

 { 

begin

 | 

exclude

 | 

include

 } 

regular-expression

 ] 

View 

Any view 

Default level 

1: Monitor level 

Parameters 

interface

 

interface-list

: Displays the GARP statistics of one or multiple ports. You can specify up to 

10 port lists.  

•

 

You can specify a single port in the form of 

interface-type interface-number

.  

•

 

You can specify a port range in the form of 

interface-type interface-number1

 

to

 

interface-type 

interface-number2

, where the end port number specified by 

interface-number2

 must be greater 

than the start port number specified by 

interface-number1

.  

|

: Filters command output by specifying a regular expression. For more information about regular 

expressions, see 

Fundamentals Configuration Guide

. 

begin

: Displays the first line that matches the specified regular expression and all lines that follow. 

exclude

: Displays all lines that do not match the specified regular expression. 

include

: Displays all lines that match the specified regular expression. 

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. 

Description 

Use 

display

 

garp statistics

 to display the GARP statistics of the specified ports. If no ports are 

specified, this command displays the GARP statistics for all ports.  

This command displays the statistics about GVRP PDUs received, transmitted, and dropped on 
GVRP-enabled ports. When the system is restarted or after you perform the 

reset garp statistics

 

command, the existing packet statistics are cleared and the system starts to collect new GARP 
statistics. With the statistics, you can judge whether a GVRP-enabled port is operating properly.  

•

 

If the number of received and transmitted GVRP PDUs on the port is the same as the remote 
port, it indicates that the two ends are transmitting and receiving GVRP PDUs properly and no 
registration information is lost.  

•

 

If the port drops GVRP PDUs, you should check its registration mode. GVRP PDUs are likely to 
be dropped if the registration mode is fixed or forbidden, because dynamic VLANs cannot be 
registered in these two modes.  

Related commands: 

reset garp statistics

.  

Examples 

# Display GARP statistics on ports Ethernet 1/0/1 and Ethernet 1/0/2.  

<Sysname> display garp statistics interface ethernet 1/0/1 to ethernet 1/0/2 

 

         GARP statistics on port Ethernet1/0/1 

 

Содержание 3100 v2 Series
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды