HP 3100 v2 Series Скачать руководство пользователя страница 147

Страница: 147 / 239

140

Field Description

Name

Name configured for the VLAN.

IPv4 address

IPv4 address of the VLAN interface (available only when an IPv4 address is
configured for the VLAN interface).

IPv4 subnet mask

Subnet mask of the IPv4 address (available only when an IPv4 address is
configured for the VLAN interface).

IPv6 global unicast
address(es)

Global unicast IPv6 address of the VLAN interface (available only when an
IPv6 address is configured for the VLAN interface).

Tagged Ports

Ports through which VLAN packets are sent tagged.

Untagged Ports

Ports through which VLAN packets are sent untagged.

interface vlan-interface

Syntax

interface vlan-interface vlan-interface-id

undo interface vlan-interface

vlan-interface-id

View

System view

Default level

2: System level

Parameters

vlan-interface-id

: Specifies a VLAN interface number, in the range of 1 to 4094.

Description

Use

interface vlan-interface

to create a VLAN interface and enter its view or enter the view of an

existing VLAN interface.

Use

undo interface vlan-interface

to remove the specified VLAN interface.

Create the VLAN before you create the VLAN interface.

To configure an IP address for a VLAN interface that will perform IP routing, use the

ip address

command in VLAN interface view.

Related commands:

display interface vlan-interface

Examples

# Create VLAN-interface 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] quit

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2]

ip address

Syntax

address

ip-address

{

mask

mask-length

}

Содержание 3100 v2 Series
















































































































































































































































Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды

HP 3100 v2 Series, Справочник по командам

Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды