HP 3100 v2 Series Скачать руководство пользователя страница 123

Страница: 123 / 239

116

Related commands:

stp mcheck

and

stp enable

Examples

# Configure the spanning tree device to operate in STP mode.

<Sysname> system-view

[Sysname] stp mode stp

stp no-agreement-check

Syntax

stp no-agreement-check

undo stp no-agreement-check

View

Ethernet interface view, port group view, Layer 2 aggregate interface view

Default level

2: System level

Parameters

None

Description

Use

stp no-agreement-check

to enable No Agreement Check on the ports.

Use

undo stp no-agreement-check

to disable No Agreement Check on the ports.

By default, No Agreement Check is disabled.

Configured in Ethernet interface view, the setting takes effect only on the interface.

Configured in port group view, the setting takes effect on all member ports in the port group.

Configured in Layer 2 aggregate interface view, the setting takes effect only on the aggregate
interface.

Configured on a member port in an aggregation group, the setting takes effect only after the port
leaves the aggregation group.

This feature takes effect only after you enable it on the root port.

Examples

# Enable No Agreement Check on Ethernet 1/0/1.

<Sysname> system-view

[Sysname] interface ethernet 1/0/1

[Sysname-Ethernet1/0/1] stp no-agreement-check

stp pathcost-standard

Syntax

stp

pathcost

standard

{

dot1d-1998

dot1t

legacy

}

undo

stp pathcost-standard

View

System view

Содержание 3100 v2 Series
















































































































































































































































Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды

HP 3100 v2 Series, Справочник по командам

Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Бренды по названию

Популярные бренды