manualshive.com logo in svg

HP 268 Pro G1 MT, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
HP 268 Pro G1 MT Скачать руководство пользователя страница 62

Unable to connect to the Internet.

Cause

Solution

Cable/DSL service is not available or has been interrupted due to 
bad weather.

Try connecting to the Internet at a later time or contact your ISP. (If 
the cable/DSL service is connected, the cable light on the front of 
the cable/DSL modem will be on.)

The CAT5 UTP cable is disconnected.

Connect the CAT5 UTP cable between the cable modem and the 
computers’s RJ-45 connector. (If the connection is good, the PC light 
on the front of the cable/DSL modem will be on.)

IP address is not configured properly.

Contact your ISP for the correct IP address.

Cookies are corrupted. (A “cookie” is a small piece of information 
that a Web server can store temporarily with the Web browser. 
This is useful for having the browser remember some specific

 

information that the Web server can later retrieve.)

Windows 10:

1.

Type 

control panel

 in the taskbar search box, and then 

select Control Panel from the list of applications.

2.

Click Internet Options.

3.

In the Browsing history section, click the Delete button.

4.

Select the Cookies and website data check box and click the 
Delete button.

Cannot automatically launch Internet programs.

Cause

Solution

You must log on to your ISP before some programs will start.

Log on to your ISP and launch the program.

Solving software problems

Most software problems occur as a result of the following situations:

●

The application was not installed or configured correctly.

●

There is insufficient memory available to run the application.

●

There is a conflict between applications.

●

All the necessary device drivers might not have been installed.

●

If you have installed an operating system other than the factory-installed operating system, it might not be 
supported on the system.

If you encounter software problems, see the applicable solutions listed in the following table.

Computer will not continue and the HP logo does not appear.

Cause

Solution

ROM issue - POST error has occurred.

Observe the beeps and lights on the front of the computer. See 

POST error messages on page 70

 to determine possible causes.

See the Worldwide Limited Warranty for terms and conditions.

54

Chapter 5   Troubleshooting without diagnostics

Содержание 268 Pro G1 MT











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды