HP 25mx Скачать руководство пользователя | Manualshive

Страница: 23 / 27

background image

21

DP Connector repair- J3

1) Use a soldering iron and a de-soldering pump to remove as much solder as

possible from one of the pin.

2) Use a hot air gun to melt the solder on the pins

3) Lift J3 from the PCB

4) Place new component on the location, and must check it can match PCB footprint

5) Soldering the new component by solder iron

6) Tear off the yellow tape on the DP connector, so that it can contact to the gasket,

EMI will be effective.

7). Please must stick a gasket on the Shielding. Find the procedure on page 22.

«
...
21
22
23
24
25
...
»

Содержание 25mx




























Отзывы:

Нет отзывов

Похожие инструкции для 25mx

S243HL - Bmii Widescreen Slim WLED Display

Бренд: Acer Страницы: 2

Бренд: Garmin Страницы: 3

Бренд: IBM Страницы: 35

ThinkVision L180p

Бренд: IBM Страницы: 28

Бренд: IBM Страницы: 23

Бренд: IBM Страницы: 4

Бренд: IBM Страницы: 30

SyncMaster 320TSn-2

Бренд: Samsung Страницы: 21

SyncMaster LD190G

Бренд: Samsung Страницы: 67

SyncMaster 460UT

Бренд: Samsung Страницы: 25

Бренд: Eneo Страницы: 56

Бренд: Wohler Страницы: 2

Бренд: Daktronics Страницы: 90

Бренд: Barco Страницы: 71

Бренд: BenQ Страницы: 36

Бренд: InFocus Страницы: 58

Бренд: BAFANG Страницы: 14

Бренд: Beurer medical Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды