background image

33444-0-0414

Page 6

GAS SPECIFICATIONS

MODEL

FUEL

INPUT

HWDV081(B)

Propane/LP -- Natural gas

8,000 Btu/hr

HWDV150(B)

15,000 Btu/hr

MANIFOLD PRESSURE

Natural gas: 4in water column pressure (W.C.)

Propane/LP gas: 10.0in W.C.

Gas Inlet

1/2 NPT

SUPPLY

MINIMUM PRESSURE

MAXIMUM PRESSURE

Natural Gas

5in W.C.

10.5in W.C.

LP Gas

11in W.C.

13in W.C.

Note: Appliance input ratings are based on sea level operation and need not be changed for operation up to 2,000 feet 

(609.6m). 

SPECIFICATIONS

MODELS

HWDV081(B)

HWDV150(B)

COMBUSTION

ATMOSPHERIC BURNER

STANDARD HEATING SPACE

233 Sq ft 

(21.65 Sq m)

478 Sq ft 

(44.41 Sq m)

EXTERNAL DIMENSIONS

HEIGHT

21-11/16in 

(550.9mm)

25-3/16in 

(639.8mm)

WIDTH

18-5/16in 

(465.1mm)

22-5/16in 

(566.7mm)

DEPTH

9in 

(228.6mm)

9-1/2in 

(241.3mm)

NET WEIGHT

29 lbs 

(13.15 kg)

40 lbs 

(18.14 kg)

MAX. GAS CONSUMPTION

8,000 Btu/hr.

15,000 Btu/hr.

SAFETY DEVICES

Safety valve (thermopile)

NOTE: 

This direct vent wall furnace is equipped for either Natural or Propane gas. Field conversion 

kits are available for purchase by calling 877-459-1583.

HIGH ALTITUDE SPECIFICATIONS

Model

0 - 2,000 feet (0 - 609.6m)

2,000 - 4,500 feet (609.6 - 1371.6m)

Main Burner Orifice/Gas Pressure

Main Burner Orifice/Gas Pressure

Natural Gas

LP Gas

Natural Gas

LP Gas

HWDV081(B)DV

#55 (4in)

#66 (10in)

#1.27 mm (4in)

#67 (10in)

HWDV150(B)DV

#48 (4in)

#56 (10in)

#51 (4in)

#57 (10in)

For elevations above 2,000 ft (609.6m), input ratings should be reduced at the rate of 4% for each 1,000 ft (304.8m) above 

sea level. Canadian High Altitudes for locations having an elevation above mean sea level between 2,000 feet (609.6m) and 

4,500 ft (1371.6m), use orifices as indicated in the following table:

Содержание HWDV081

















































Отзывы: