17
Operations
To Start
DANGER: Do not point wand or trigger gun at
yourself or at any person. Bodily injury may result
from water under high pressure.
WARNING: Wear eye, ear, hand, foot, and skin
protection at all times while operating pressure
washer.
IMPORTANT: The water must be turned on before
starting. Running the pump dry will cause damage
and void warranty.
IMPORTANT: Do not allow the machine to run with
trigger of trigger gun released for more than 10
minutes at any one time or damage to pump may
occur.
WARNING: If ignition or flame failure is experi-
enced, discontinue use of burner at once by
turning burner switch off. Have cause of failure
corrected by an authorized service technician.
After corrections are made, refer to OPERATION for
start-up instructions.
1. Connect electrical cord and test GFCI device.
2. Turn on water supply.
3. Turn on gas supply.
4. Grasp wand firmly. Turn on pump switch.
5. Turn on burner switch, and adjust thermostat to
desired temperature.
6. Squeeze trigger of trigger gun. The pilot will auto-
matically ignite, quickly followed by the firing of the
burner ring. If ignition does not take place within 5
to 7 seconds see
Troubleshooting Guide
in this
manual. When the trigger of the trigger gun is
released or thermostat setting is reached, the
burner will turn off.
To Clean
DANGER: Do not place hands or fingers in front of
high pressure spray. Bodily injury may result.
1. Insert the detergent inlet line into the container of
mixed detergent. The detergent metering valve on
the chassis allows the detergent flow to be
controlled.
2. Adjust the width of the pressure nozzle spray
pattern to meet your cleaning needs. Adjustment is
made by rotating the outer housing of the pressure
nozzle. The spray pattern can be adjusted from 0
degrees solid stream to 80° fan spray. Release the
trigger of the trigger gun prior to making any spray
pattern adjustments.
3. Wash from the bottom to the top, using side to side
motions. This washes away heavy dirt and allows
the detergent to soak as you work toward the top.
4. Do not wash at a 90
°
angle to work (straight at it).
This will allow water to splash back at you and
reduces your cleaning power. Wash at a 30
°
to 60
°
angle to the work. This will allow the water to
splash away from you and the water will wash the
dirt away faster and easier.
5. Use the full width of the spray pattern to wash in a
wide path. Overlap spray paths for complete
coverage. Wash from side to side, using slow,
steady motions.
6. The nozzle should be 12" to 24" from work, closer
for tough areas. Be careful on painted or delicate
surfaces, the pressure may damage surface if
nozzle is too close.
7. Small parts should be washed in a basket so the
pressure does not push them away. Larger, light-
weight parts should be clamped down so the
pressure does not push them away.
8. To rinse, turn the detergent metering valve clock-
wise. Always rinse with cold water after using
detergent. Rinse from the top to the bottom to
prevent detergent from dripping onto a rinsed area.
For the best results, contact your Hotsy dealer to
help you select the best detergent for your applica-
tion.
Hotsy 771 / 772 8.941-246.0 - Y
Solid
Stream
Fan
Spray
Outer
Housing
Содержание 1.109-037.0
Страница 2: ...2 Hotsy 771 772 8 941 246 0 Y Machine Data Label ...
Страница 22: ...22 Notes Hotsy 771 772 8 941 246 0 Y ...
Страница 23: ...23 Parts Parts 1 109 611 0 1 109 037 0 HOTSY 771 772 Hotsy 771 772 8 941 246 0 Y ...
Страница 28: ...28 Coil Outlet 1 5 3 4 2 6 Hotsy 771 772 8 941 246 0 Y ...