Page 31
Installation Instructions
DELIVERY ACCESS
First, locate the dimensions of your spa on the following chart. The
dimensions shown are the measurements of the spa in the vertical
position, laid on its side.
Model
W
L
H
RELAY
(RELE)
92 cm (36")
213 cm (84")
213 cm (84")
RHYTHM
(RHYE) 92 cm (36")
213 cm (84")
213 cm (84")
PROPEL
(PRPE) 84 cm (33")
208 cm (82")
208 cm (82")
STRIDE
(STDE)
74 cm (29")
213 cm (84")
165 cm (65")
SX
(SXE)
84 cm (33")
196 cm (77")
183 cm (72")
TX
(TXE)
74 cm (29")
183 cm (72")
183 cm (72")
Next, contact your dealer to find the height and width added by the
delivery cart which the dealer will use to deliver your new spa. Use
the height of the cart plus the dimension shown as H to determine the
vertical clearance required to pass the spa and cart. Use the width of the
cart, or dimension W, whichever is greater, to determine the maximum
width of clearance necessary.
NOTE:
It may be necessary to allow for additional over-head clearance if
the spa will be rolled up or down an incline or moved up or down a short
flight of stairs.
Use the information above to determine the requirements
for access to your desired location.
It may be necessary to remove a gate,
part of a fence, or other movable
obstructions in order to roll the
spa to its installation site.
If the spa has to be taken
off the cart to go over a
wall (either because the
entry area is too narrow,
the eaves are too low, the
corner is too tight, or the
stairway is too steep),
a crane will be required.
This is a common
practice.
The crane has a truck-mounted boom which can fit right in your
driveway. It must be run by a licensed and insured operator. For a
charge, the crane operator will lift your spa over walls, buildings, or any
other obstruction and place it as close to the installation site as possible.
Crane delivery typically takes an average of 60 minutes to complete.
NOTE:
If your spa delivery requires the use of a crane, you may be
required to pay for its services at the completion of the delivery.
GROUND PREPARATION
Your
HOT SPRING
spa has been engineered to perform on several
kinds of surfaces. While a concrete slab is best for long-term use*, other
foundations are acceptable so long as a level base is prepared prior to
delivery.
*NOTE:
A reinforced concrete pad at least four inches thick or a deck
that is able to withstand more than 586 kg/m² is recommended for the
RELAY
spas, 610 kg/m² is recommended for the
RHYTHM
spa, 505
kg/m² is recommended for the
PROPEL
spa.
INSTALLATION NOTES:
If you are purchasing a deck package or a gazebo with your spa, a solid
foundation becomes mandatory. Placing them on any surface other than
a single level pad could create problems with their installation. Pictured
at right are a few of the recommended surfaces.
As a homeowner, it is your responsibility to provide a suitable, level
foundation for your spa. Keep in mind that most delivery crews are not
equipped to level and prepare spa sites.
If you are interested in having a concrete slab, brick surface, or wood
deck installed, your
HOT SPRING
dealer should be able to suggest a
qualified, licensed contractor.
NOTE:
In order for the spa to operate properly and the internal plumbing
to drain completely, you must ensure that the spa is level after it has
been installed. Your
HOT SPRING
spa delivery crew can help you
perform the procedure.
How is your width clearance?
Check all gates
Protruding electric meters
Gas meters
A/C units
Is the path clear?
Move away branches, dog
houses, firewood, etc.
If there is a 90º turn, can we clear it?
(The spa will not bend)
No more than 6 consecutive
stairs without a landing
STREET
BACK YARD
(GARDEN)
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
