4
GB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Installation
WARNING - THIS APPLIANCE MUST BE
EARTHED.
Mains Connection
Your cooker should have been checked to ensure that
the voltage corresponds with your supply voltage, this
is stated on the rating plate, which is situated on the
outer rear panel.
The model number and serial number are located
on the front of the cooker, as shown on the Feature’s
page.
The cooker must be connected by a competent person
such as one who is a, NICEIC registered contractor
to a suitable double-pole control unit with a minimum
rating of 32A and a minimum contact clearance of
3mm (applicable to newer properties, older properties
where a 30A double pole control unit and a minimum
contact clearance of 3mm is acceptable).
The double pole control unit should be fitted adjacent
to the cooker, in accordance with IEE regulations. The
control unit must be within 2 metres of but not directly
above the appliance and should be easily accessible
in the event of an emergency.
The power supply cable should conform to B.S.6004
with a conductor size of 6mm2, minimum.
Access to the mains terminals is gained by removing
the rear access cover. The mains cable must pass
through the cable clamp adjacent to the terminal block.
Sufficient cable should be used to allow the cooker to
be pulled out for servicing.
Ensure that the mains cable is routed away from
any brackets affixed to the rear panel and is not
trapped to the rear wall when pushing the cooker
into position between cabinets.
Levelling
Four feet are fitted which can be adjusted up or down
to set the height (900mm - 930mm) and level the
cooker.
The feet can be simply screwed in or out to lower or
raise the cooker.
After the correct height is achieved, lock the feet into
position by tightening the locking nut using an open
ended spanner.
CAUTION: Some soft floor coverings may get
damaged if the cooker is not moved carefully.
NOTE: Ensure oven shelves are level by using a spirit
level on the rod shelves.
Siting the Cooker
The cooker is designed to fit between kitchen cabinets
spaced 600mm apart. The space either side need
only be sufficient to allow withdrawal of the cooker for
servicing and cleaning.
It can be used with cabinets one side or both as well
as in an angled corner setting. It can also be used
freestanding.
Adjacent side walls which project above hob level,
must not be nearer to the cooker than 150mm and
should be protected by heat resistant material. Any
overhanging surface or cooker hood should not be
nearer than 650mm.
Note: This appliance must NOT be fitted on a
platform.
Moving the Cooker
Before moving your cooker, switch off at the cooker
control unit, ensure that it is cool.
Open the grill door sufficiently to allow a comfortable
grip on the underside front edge of the oven roof,
avoiding any grill elements.
Radio Interference
This appliance conforms to EN 55014 regarding
suppression of radio and television interference.
Note: Take care in moving the cooker as it is heavy.
Take care to ensure that any floor covering is not
damaged.
Safety Chain
! In order
to prevent
accidental
tipping of the
appliance, for
example by
a child clim-
bing onto the
oven door, the
supplied safety
chain MUST be
installed!
The cooker is fitted with a safety chain to be fixed by
means of a screw (not supplied with the cooker) to
the wall behind the appliance, at the same height as
the chain is attached to the appliance.
Choose the screw and the screw anchor according
to the type of material of the wall behind the applian-
ce. If the head of the screw has a diameter smaller
than 9mm, a washer should be used. Concrete wall
requires the screw of at least 8mm of diameter, and
60mm of length.
Ensure that the chain is fixed to the rear wall of the
cooker and to the wall, as shown in figure, so that
after installation it is tensioned and parallel to the
ground level.
