Hotpoint EW74, Инструкция по установке и эксплуатации

Страница: 21 / 28

GB
2 1
Care and Cleaning
Door and Control Panel ( Glass )
Regularly wipe with a clean, damp cloth and polish
with a clean, dry cloth.
Door a n d Con t ro l P a ne l Trim s ( S ta in l e ss S t ee l )
Regularly wipe with a clean, damp cloth and polish
with a clean, dry cloth.
W A R NING : TO A V OID ELE CT R IC SH OC K ,
B EF O R E R EPL ACING T HE O V E N L IG H T ,
SW ITC H T HE COO K E R O FF AT T HE COO K E R
CONT R O L UNIT ( a n d all ow t o coo l i f t he o v en
h as been u s e d ).
R e pla cemen t o f t he O v en L igh t
Unscrew the glass cover, using a suitable cloth to
protect the fingers and remove carefully. Unscrew
the existing light bulb, and remove. Screw the new
bulb into position and replace the glass cover, with
metal washer, until positioned securely.
C LE ANING T HE DOO R S
T ak e pa r t icu la r c a re no t t o da m a ge t he inner
s ur fa ce o f t he d oor inner g lass t h at i s co at e d wi t h
a he at re fl ec t i v e lay er . Do no t u s e s couring pads ,
or a br as i v e p ow d er , which wi ll s cr at ch t he g lass .
E n s ure t h at t he g lass pa ne l i s no t s ub j ec t e d t o
a n y s h a r p mech a nic al b l ow s .
Stubborn stains can be removed by using a fine
steel wool soap pad. For slight soiling the inner
glass panel may be cleaned, while still warm,
without removing it from the door. After cleaning,
rinse and dry with a soft cloth.
S ID E O PE NING DOO R S
C l e a ning t he d oor g lass i s t he sa me as t he d ro p
d own d oor s , e x ce pt tak e c a re t o s u pp or t t he weigh t
o f t he inner g lass when remo v ing a n d re f i tt ing .
D R O P DO W N DOO R S
R emo v e t he d oor inner g lass as f o ll ow s .
1. Open the door fully and remove the extrusion
end caps (This should be done by hand but if it
proves too difficult, simply lift the inner glass to
ease the end caps out of position).
NOTE: If you need to use a tool - be
careful not to damage the extrusion or
end cap.
Top filler cap Remove both screws to
remove top filler cap
2. Carefully slide the inner glass towards you and
withdraw it from its locating slots. Ensure that
the door is not allowed to slam shut, due to the
reduction in door weight. Clean the glass as
described above.
3. The inside of the outer door glass can now be
cleaned while still fitted to the cooker.
N E V E R O PE R AT E T HE COO K E R W IT H OUT T HE
INN E R DOO R G L A SS IN P O S ITION .
R e f i t t he d oor inner g lass as f o ll ow s .
1. Open the door fully.
2. Locate the inner door glass into its slots, so that
the printing is readable from the face nearest the
oven in the closed position and the widest black
band is towards the bottom of the door. The
inner door glass has a special reflective coating
on one side, in order to minimise surface
temperatures and energy consumption during
use, it is important it is fitted correctly.
3. Carefully slide the glass into its slots as far as it
will go and replace the end caps.