Hoshizaki KM-520MRJZ Скачать руководство пользователя страница 33

Страница: 33 / 41

2. Appliance Startup and Bin Control Check

WARNING

• All parts are factory-adjusted. Improper adjustments may adversely affect safety,

performance, component life, and warranty coverage.

• Make sure the icemaker has been installed as outlined in this manual and that the

water supply is on.

• Improper adjustment may adversely affect safety, performance, component life,

and warranty coverage.

NOTICE

• If the icemaker is turned off, wait for at least 3 minutes before restarting the

icemaker to prevent damage to the compressor.

• To prevent damage to the water pump seal, do not leave the control switch in the

"PUMP" position for extended periods when the water tank is empty.

• At startup, confirm that all internal and external connections are free of leaks.
• Do not allow top kits or top kit risers (if applicable) to interfere with the bin control

lens sensing area or the icemaker will not operate properly.

Additional Notice for Remote Models

• The icemaker must have power for a minimum of 4 hours prior to startup to

prevent compressor damage.

1) If not already removed, remove the front, top, and right side panels and base cover.

Make sure the bin control setting has been adjusted as outlined in "II.I.1. Bin Control
Setting."

2) Open the water supply line shut-off valve(s).
3) Move the mode switch on the control box to the "ICE" position, then move the control

switch to the "ON" position. Turn on the power supply, and allow the icemaker to
operate.

4) Confirm the control board "BIN CLS"

LED is off (bin empty). See Fig. 16.

Ice Level in Bin

Control Board "BIN CLS" LED

Empty

OFF

Full

5) If the control board "BIN CLS" is on

(indicating a full bin), correct any
interference from the top kit or top kit
riser (if applicable).

Fig. 16

Control Board

BIN CLS LED

Bin Control Setting

Содержание KM-520MRJZ










































Результаты поиска

Содержание KM-520MRJZ

Отзывы:

Похожие инструкции для KM-520MRJZ

Бренды по названию

Популярные бренды

Hoshizaki KM-520MRJZ, Инструкция по эксплуатации

Результаты поиска

Содержание KM-520MRJZ

Отзывы:

Похожие инструкции для KM-520MRJZ

Бренды по названию

Популярные бренды