Hoshizaki KM-520MRJZ Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 41

background image

13

B. Checks Before Installation

• Visually inspect the exterior of the shipping container and immediately report any

damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.

• Remove the shipping carton, tape, and packing material. If any are left in the icemaker,

it will not work properly.

• See the nameplate on the rear panel, and check that your voltage supplied corresponds

with the voltage specified on the nameplate.

• Remove the panels to prevent damage when installing the icemaker. See "II.C. How to

Remove Panels."

• Remove the package containing the accessories.
• Remove the protective plastic film from the panels. If the icemaker is exposed to the sun

or to heat, remove the film after the icemaker cools.

• Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the

fan blade (if applicable) turns freely.

• Check that the compressor is snug on all mounting pads.
• The icemaker can be installed on a dispenser unit or ice storage bin. The ice storage

bins listed below are recommended.

Model Number Bin Width

Recommended Hoshizaki Ice Storage Bin

KM-350M_J
KM-520M_J(Z)
KM-660M_J(Z)

22" or Wider B-300 Series

For further options, contact your local Hoshizaki distributor.

•

NOTICE!

Remote models must be connected to an appropriate remote condenser

unit. The remote condenser units listed below are recommended. Connection to a
different remote condenser unit will void the warranty unless Hoshizaki approves
a different remote condenser unit for your specific application. For further
details, contact your local Hoshizaki distributor.

Model Number Recommended Hoshizaki Remote Condenser Unit

KM-520MRJZ
KM-660MRJZ

URC-5FZ

C. How to Remove Panels

See Fig. 1

• Front Panel: Remove the screw. Lift up and

towards you.

• Top Panel: Lift up at front slightly, push rearward

and lift off.

• Right Side Panel: Remove the screw. Slide the

right front corner to the right slightly, then push

rearward and lift off.

• Front Insulation Panel: Lift up slightly and pull

towards you.

• Base Cover: Lift up slightly and pull towards you.

Fig. 1

Top Panel

Front Insulation Panel

Front
Panel

Base Cover

Screw
Right Side Panel

Model Shown: KM-520MAJ

«
...
11
12
13
14
15
...
»

Содержание KM-520MRJZ










































Отзывы:

Нет отзывов

Похожие инструкции для KM-520MRJZ

Бренд: Caffitaly System Страницы: 28

Бренд: Dacor Страницы: 16

Бренд: Viconte Страницы: 16

Бренд: Kalorik Страницы: 12

Бренд: Salton Страницы: 16

Бренд: U-Line Страницы: 19

ESPRESSO DELUXE

Бренд: Gaggia Страницы: 53

Бренд: Smeg Страницы: 27

Бренд: Orbegozo Страницы: 25

Бренд: Hamilton Beach Страницы: 10

Бренд: nedis Страницы: 32

Hotel Dispenser CD 40030 Series

Бренд: Ice-O-Matic Страницы: 21

Бренд: La Pavoni Страницы: 44

Бренд: Lagrange Страницы: 66

Бренд: Brandt Страницы: 23

Бренд: Clas Ohlson Страницы: 28

Бренд: KitchenAid Страницы: 8

HDC10LBS - 10c Coffeemaker & SS

Бренд: Haier Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды