horsch Terrano 4.3 GX Скачать руководство пользователя страница 81

Страница: 81 / 114

Operation | 8

60084498 • 01 • 06/2022 • en

8.4 Traction intensifier

If traction intensifiers are enabled, part of the load caused by the bottom pull will al-
ways be transferred to the tractor.

1. Disable traction intensifiers prior to connecting and unhitching, on loose soils

or shallow cultivation.
For this purpose turn the lock valve towards the back to position "0" (see sym-
bol plate).

2. Set the lock valve across the travel direction to use the traction intensifier.

3. For use in the field always set the

Lift/Lower

control unit to the floating posi-

tion.

Hydraulic valve block traction intensifier with symbol plate

Traction intensifier lock valve – position "0"

8.5 Use in the field

8.5.1 Work instructions

NOTE

Please note:

The machine must be in horizontal position when used in the field.

Do not drive backwards with the machine lowered. The components are not
designed for this and could be damaged.

Содержание Terrano 4.3 GX



















































































































Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды

horsch Terrano 4.3 GX, Руководство по эксплуатации

Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды