horsch Terrano 4.3 GX Скачать руководство пользователя страница 60

Страница: 60 / 114

7 | Optional equipment

60084498 • 01 • 06/2022 • en

7.1.2 Hydraulic brake

The hydraulic line controls the brake power on the brake cylinders.

The brake inlet pressure must not exceed 150 bar.

Overview

Hydraulic brake

1 Hydraulic coupling for brake

2 Drain valve

3 Breakaway valve for emergency

operation

4 Pressure accumulator

5 Wheel cylinder

6 Measuring coupling

Connect the brake

WARNING

Danger of traffic accidents!

The cable may be caught by other machine parts and thus trigger flat-out braking
when cornering.

Fasten the cable in such a way, that it cannot be caught in any place.

WARNING

Danger of traffic accidents caused by brake failure due to empty
pressure accumulator!

After each connecting and before starting to travel, fill the pressure accumu-
lator for the emergency brake.

Fully kick down the brake pedal on the tractor for this purpose.

1. When hitching up connect the hydraulic brake line with the brake line on the

tractor.

2. Fasten the breakaway protection cable at a suitable place on the tractor.

Содержание Terrano 4.3 GX



















































































































Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды

horsch Terrano 4.3 GX, Руководство по эксплуатации

Результаты поиска

Содержание Terrano 4.3 GX

Отзывы:

Бренды по названию

Популярные бренды