horsch LEEB PT 330 Скачать руководство пользователя страница 55

Страница: 55 / 203

4.4.6 Swivelling facility

CAUTION

Danger of accident caused by operating

the swivelling facility while driving. Do not

operate the locking lever for the swivelling

facility while driving!

Pulling the locking lever (4) enables the swiv-

elling facility. It enables free swivelling of the

driver's seat to the right against the stop position.

NOTE

Once the setting has been made, the locking le-

ver must noticeably click into place. The driver's

seat should be locked against being turned to

any other position.

4.4.7 Longitudinal adjustment

CAUTION

Danger of accident when operating the lon-

gitudinal adjustment while driving. Do not

operate the locking lever while driving!

By pulling the operating lever (5) up the longi-

tudinal adjustment is released and the driver's

seat can be moved forward or backward.

NOTE

Once the setting has been made, the locking le-

ver must noticeably click into place. The driver's

seat should be locked against being moved to

any other position.
Do not lift the locking lever with your leg or calf.

4.4.8 Inclination and depth setting

Both the inclination and the depth of the seat

area can be individually adjusted.

Pull the left handle (6) up to adjust the seat incli-

nation. The seat can be inclined to the desired

position by simultaneous loading and unloading

of the front and rear seat areas.

Pull the right handle (7) up to adjust the seat

depth. If the seat area is at the same time shifted

forward or backward, the desired position is

reached.

Содержание LEEB PT 330












































































































































































































Результаты поиска

Содержание LEEB PT 330

Отзывы:

Похожие инструкции для LEEB PT 330

Бренды по названию

Популярные бренды

horsch LEEB PT 330, Руководство по эксплуатации

Результаты поиска

Содержание LEEB PT 330

Отзывы:

Похожие инструкции для LEEB PT 330

Бренды по названию

Популярные бренды