horsch LEEB PT 330 Скачать руководство пользователя страница 39

Страница: 39 / 203

Curb weight [kg]

14000

max. perm. total weight on road [kg]

18000

max. perm. total weight in field [kg]

20000

max. perm. axle load on road [kg] front / rear

8000 / 10000

max. perm.

axle load in field [kg]

10000 / 11000

Ground clearance [mm]

1400 - 1600

Wheel base [mm]

4600

Track widths [mm]

2250 - 3000 infinitely variable

Length [mm]

8700

Height [mm]

3990

3.2 Technical data of

vehicle

NOTE:

•

Deviations due to technical further development reserved.

•

The weight of the machine depends on the equipment; data with minimum equipment

•

The permissible transport heights and transport width for transport in road traffic may differ from country to country.

Comply with the national registration regulations.

Содержание LEEB PT 330












































































































































































































Результаты поиска

Содержание LEEB PT 330

Отзывы:

Бренды по названию

Популярные бренды

horsch LEEB PT 330, Руководство по эксплуатации

Результаты поиска

Содержание LEEB PT 330

Отзывы:

Бренды по названию

Популярные бренды