horsch LEEB PT 330 Скачать руководство пользователя страница 109

Страница: 109 / 203

8.6 Hydraulic oil

NOTE

ATTENTION! Do not mix different oils. Use

only the prescribed specification!

Before changing the oil type, you should

consult the Customer Service.

ATTENTION! We strictly advise you to refrain

from using bio-hydraulic oils.

Should the use of bio-hydraulic oils be nec-

essary in isolated cases, you should strictly

consult the Customer Service.

8.6.1

Hydraulic oil specifications

The following hydraulic oils have been approved

for use:

HLP

DIN 51524-2

Viscosity class ISO-VG 46

HLP-D

DIN 51524-2

Viscosity class ISO-VG 46

HVLP

DIN 51524-3

Viscosity class ISO-VG 46

HVLP-D

DIN 51524-3

Viscosity class ISO-VG 46

NOTE

We recommend using HVLP.

In contrast to HLP, these oils are characterized

by their improved absorption of water and dirt

as well as their wider temperature range.

Demanded cleanliness class: ISO 4406

18/16/13

109

Содержание LEEB PT 330












































































































































































































Результаты поиска

Содержание LEEB PT 330

Отзывы:

Бренды по названию

Популярные бренды

horsch LEEB PT 330, Руководство по эксплуатации

Результаты поиска

Содержание LEEB PT 330

Отзывы:

Бренды по названию

Популярные бренды