horsch Leeb 4 AX Скачать руководство пользователя страница 131

Страница: 131 / 161

2. Check pressure in air reservoir

Connect a pressure gauge to the air res-

ervoir test port.
Nominal value 6.0 to 8.1

+ 0.2

bar

3. Check pressure of brake cylinders

Connect a pressure gauge to the brake

cylinder test port.
Nominal value: 0.0 bar with the brake not

operated

4. Visual inspection on brake cylinder

Check the brake cylinder for damage.

Replace damaged parts.

5. Joints on brake valves, brake cylinders and

brake linkages must be light moving.

Lubricate or lightly oil if necessary.

Maintenance of the axle

Checking the bearing play of the

wheel hub (workshop work)

WARNING

Danger of crushing, shearing, cutting, cutting off,

being caught, wound up, pulled in, caught and

knocked by accidental starting and rolling away

of the tractor - machine combination.

Secure both tractor and crop protection sprayer

against accidental starting and unintended roll-

ing before you start working on the machine.

To check the bearing play of the wheel hubs

the axle must be lifted until the tyres are off the

ground. Now release the brake. Place a lever

between tyres and ground and check the clear-

ance.

Adjust the

bearing play if it can be felt.

1. Dismantling the wheels and hub capsules.
2. Remove the cotter pin from the castle nut.

3. Tighten the castle nut with torque spanner

while turning the wheel hub. If an axle nut

wrench is used for this purpose, tighten the

castle nut until the freewheeling wheel hub

is slightly retarded.

4. Turn the castle nut back to the next possible

cotter pin hole. In case it is already aligned

with the hole, turn to the next hole (max. 30°).

5. Insert the cotter pin and bent it slightly open.
6. Fill some long-term grease in the hub cap-

sule.

7. Apply long-term grease on the thread of the

capsule and knock into the wheel hub or screw

down with torque spanner.

8. Assemble the wheels again.

Replacing the grease of the wheel

hub bearing

WARNING

Danger of crushing, shearing, cutting, cutting off,

being caught, wound up, pulled in, caught and

knocked by accidental starting / rolling away of

the tractor - machine combination or incorrect

jacking of the machine.

Secure the tractor and crop protection sprayer

against unintentional starting/rolling away before

beginning to work on the machine. Jack up the

machine in a safe condition and secure against

falling!

1. Jack up the machine in a safe condition and

release the brake.

2. Remove wheels and dust caps.
3. Remove the cotter pins and unscrew the

axle nut.

4. Dismantle the wheel hub with brake drum,

tapered roller bearing as well as sealing ele-

ments with a suitable puller off the steering

knuckle.

125

Содержание Leeb 4 AX


































































































































































Результаты поиска

Содержание Leeb 4 AX

Отзывы:

Похожие инструкции для Leeb 4 AX

Бренды по названию

Популярные бренды

horsch Leeb 4 AX, Руководство по эксплуатации

Результаты поиска

Содержание Leeb 4 AX

Отзывы:

Похожие инструкции для Leeb 4 AX

Бренды по названию

Популярные бренды