horsch Focus 4 TD Скачать руководство пользователя страница 63

Страница: 63 / 108

Operation | 7

60059040 • 02 • 07/2021 • en

Position of control units
during road travel

Position

Control unit

Floating posi-
tion

Locked position Supply

Lift / lower

Hydraulic valve block

Fan 1

7.2.3 Parking

DANGER

Serious accidents from loss of stability!

Park the machine only on a level and firm ground.

NOTE

Clean the machine and prepare properly before parking it for an extended
period; see chapter

Care and Maintenance.

Thoroughly clean hopper and fertiliser equipment. Fertiliser is aggressive and
speeds up the corrosion process. It especially attacks galvanised components
like bolts.

Clean all metering units.

Preferably park the drill in a shed so that no moisture can accumulate in hop-
per, metering units and the seed hoses.

Lift the machine completely.

Unfold the machine completely, if necessary.

Fold the support leg out and secure it with the bolt.

Lower the machine on the parking support.

Содержание Focus 4 TD













































































































Результаты поиска

Содержание Focus 4 TD

Отзывы:

horsch Focus 4 TD, Руководство по эксплуатации, Страница: 63 / 108

Результаты поиска

Содержание Focus 4 TD

Отзывы: