horsch Focus 4 TD Скачать руководство пользователя страница 60

Страница: 60 / 108

7 | Operation

60059040 • 02 • 07/2021 • en

Please consider also a loop for cornering.

Attach the clamping brackets again.

7.1.1 Adapting the drawbar

For hitching up with towing eye or ball head, the drawbar needs to be adapted to
the hitching height.

1. Back the tractor carefully up to the machine.

2. Connect the hydraulic lines to the tractor.

3. Open the lock valve on the drawbar.

4. Set the height of the drawbar.

5. Close the lock valve again.

Drawbar – swinging drawbar hitching

Drawbar cylinder

Lock valve

7.2 Connecting / Parking

DANGER

Serious accidents when manoeuvring and coupling!

Keep an eye on your environment.

Order persons to leave the manoeuvring area around the machine.

Instruct persons to leave the area between tractor and machine.

No person must be present in the danger zone when the tractor approaches
the machine or moves away from it!

Trigger movements of the three-point power jack only from outside the
danger zone.

WARNING

Leaking hydraulic fluid can cause serious injuries! Danger of injury by
unwanted machine movements.

Connect and disconnect the hydraulic lines only when the hydraulics are
without pressure on both tractor and machine.

Содержание Focus 4 TD













































































































Результаты поиска

Содержание Focus 4 TD

Отзывы:

horsch Focus 4 TD, Руководство по эксплуатации, Страница: 60 / 108

Результаты поиска

Содержание Focus 4 TD

Отзывы: