horsch Focus 4 TD Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 108

horsch Focus 4 TD Скачать руководство пользователя страница 59

60059040 • 02 • 07/2021 • en

59

7 Operation

WARNING

Ø

Whenever working on the machine pay attention to the associated safety
notes in the chapter "Safety and Introduction" as well as the accident preven-
tion regulations!

7.1 Initial commissioning/tractor change

During initial commissioning and when changing the tractor, the machine must be
adapted to the tractor.

WARNING

Serious crushing due to lowering / dropping machine parts

Ø

No persons may stay under raised machine parts.

Ø

Order persons to leave the danger zone around the machine. Make sure be-
fore folding that no persons are present in the danger zone.

Ø

Comply with the accident prevention instructions.

Adapting the hose connection

The hose bracket must be adapted to the tractor.
The hoses should be routed here in such a way that hoses and couplings will not be
damaged under any operating conditions in the field, in transport position and
when cornering.

A

B

B

B

B

Adapting the hose connection

A

Screws to adapt the position of the hose brackets

B

Clamping brackets to adapt the free hose lengths

Adapt the position of the hose
bracket

Ø

Loosen the screws.

Ø

Slide the hose bracket one bore forward or backward, depending on the posi-
tion. There should be sufficient ground clearance when lifting/lowering and
when cornering.

Ø

Retighten the screws.

Adapting the hose lengths

Ø

Adjust the free length of the hoses to the tractor. For this purpose loosen the
clamping brackets and move the hoses accordingly.

«
...
57
58
59
60
61
...
»

Содержание Focus 4 TD













































































































Отзывы:

Нет отзывов