horsch 420016020001 Скачать руководство пользователя страница 67

Страница: 67 / 84

Omnis FT Owner’s Manual – Ver. 2.0 06/2020

www.horsch.com

SCH

*Illustration may not depict the correct disc leveler. Illustration is for reference only.

Notes on cleaning:

The mechanical seals of the disc hubs are very sensitive. If water has entered them and the machine is

then parked over a longer period of time, damage may occur.

This can cause corrosion, and both mechanical seal rings may stick together. The mechanical seal rings

will then rotate around the O-ring and damage it. Oil could run out of the hub and the bearing would be

damaged after a short while with no lubrication.

• Bearings must therefore not be cleaned with high pressure cleaning equipment.

• Before longer periods of rest, the bearing locations should be sprayed with a rust

dissolver/inhibitor, or similar lubricant.

Before resuming operation, the discs should be turned by hand and checked for

unrestricted rotation.

The disc hub (illustrated on the following page) is oil filled as mentioned above. If

the seals or O-rings are damaged and further service is required, replace the seals

and O-rings, and fill the hub with 1.0 ounces of oil industrial gear lubricant, Renolin

Unisyn CLP 220 205L, or equivalent fully synthetic based on polyalphaolefins.

(See Omnis FT Parts Catalog – 34189000 Disc Leveler Bearing)

Содержание 420016020001





















































































Результаты поиска

Содержание 420016020001

Отзывы:

Бренды по названию

Популярные бренды

horsch 420016020001, Руководство пользователя

Результаты поиска

Содержание 420016020001

Отзывы:

Бренды по названию

Популярные бренды