horsch 420016020001 Скачать руководство пользователя страница 61

Страница: 61 / 84

Omnis FT Owner’s Manual – Ver. 2.0 06/2020

www.horsch.com

SCH

Parking the Machine

Only park the machine on a firm and level surface.

1. Follow the proper Unhitching procedure noted on the previous pages.

2. Insert the rear transport axle cylinder yellow safety stops (x2) and front cylinder depth stops.

3. Lower the front hitch hydraulic jack

(3)

or place the manual crank jack in the appropriate location.

4. Rest the machine on the jack.

5. Disconnect hydraulic lines and road lighting equipment.

6. Remove the safety chain and unhitch the drawbar pin from the tractor’s coupler ring and machine.

WARNING! Keep hands clear.

Put a block under the front hitch jack stand, as there is

excessive amount of weight from front hitch and machine. Be sure to install any yellow

safety stops into position on the rear cylinders and flip over depth stops to the front hitch

cylinder as needed. Chock the tires to prevent against any machine rolling.

Front Hitch Jack Stand Front Cylinder Safety Stops Rear Cylinder Safety Stops

Содержание 420016020001





















































































Результаты поиска

Содержание 420016020001

Отзывы:

Похожие инструкции для 420016020001

Бренды по названию

Популярные бренды

horsch 420016020001, Руководство пользователя

Результаты поиска

Содержание 420016020001

Отзывы:

Похожие инструкции для 420016020001

Бренды по названию

Популярные бренды