horsch 420016020001 Скачать руководство пользователя страница 26

Страница: 26 / 84

26 Omnis FT Owner’s Manual – Ver. 2.0 06/2020

www.horsch.com

SCH

Information Regarding Safety

The following warnings and safety instructions apply to all sections in these operating instructions.

Safety Symbols on the Machine:

Read and adhere to the operating instructions before starting up the

machine!

Stay clear of swinging area of retractable and extendible machine parts!

Switch the engine off and pull out the key before starting maintenance and repair
work!

Never reach into areas where there is a risk of crushing, as long as parts could still
be moving!

Watch out for fluids spraying out under high pressure, follow the operating

instructions!

It is only permitted to remain in the danger zone if the safety support is in place!

When hitching up the machine and when operating the hydraulic system, no per-

sons should be between the machines!

No passengers are allowed to ride on the machine!

Do not climb on rotatable parts. Use mounting steps provided for this purpose!

Lifting hook; attach lifting tackle (chains, ropes, etc.) here when performing loading

work!

Содержание 420016020001





















































































Результаты поиска

Содержание 420016020001

Отзывы:

Похожие инструкции для 420016020001

Бренды по названию

Популярные бренды

horsch 420016020001, Руководство пользователя

Результаты поиска

Содержание 420016020001

Отзывы:

Похожие инструкции для 420016020001

Бренды по названию

Популярные бренды