background image

 

 

 
 

Programming Guide for the JR 8103 Heli radio system 

 

The following is a programming example for a helicopter using the 8103-heli radio.  If you 

follow along, several features of the 8103 will be demonstrated, which should help better understand the 
abilities of the system.   

 

System Set-Up Mode 

 
 

To start with we will open a clear model, so press and hold the up and down keys together and 

flip the power switch on and then release the up and down keys.  Press the + and – keys to go into model 
select.  Press the + key until you get to a clear model.  Then press the up key twice to get to the model 
type.  To get to the correct type, press the + key to get to HELI, if it is not already in HELI mode.  Next 
you will press the up key to model reset.  Press CLR so that it will restore the system to factory defaults.  
Press the up key to select the modulation of the system.  Here you will use the + and – keys to set this to 
the desired modulation.  Press the up key three times, to set the input selection.  Now you will press the 
+ key to set the aux 2 to INH. Press the CH key so the arrow now points at GEAR.  Here you will press 
the + key to make this say INH.  Press the UP key one time, and this will bring you to SWASH TYP.  
This is where you can set the radio for CCPM.  Press the + key one time for 2 servo – 180 degree, again 
for 3 servo – 120 degree, and once more for 4 servo 90 degree.  If you do not have a CCPM helicopter, 
leave this at 1 servo NORM.  If it is CCPM, choose the type of set up you have.  Your instructions for 
the helicopter should have this information listed as to which type it is.  Then you can press the up key 
till you get to the name selection, and re-name the model.  At this point we have set up the system mode 
for our helicopter.   
 

Function Mode 

 
 

Next we will set up the function mode of transmitter.  If you are still in the system mode, just 

press the up and down keys together twice, or turn the radio off and back on, and press the up and down 
keys together again.  This will get you into the function mode. 
 

Dual Rate and Exponential Set-Up 

 
 

Now that we are in the function mode, it brings you to the dual rate set-up.  You can set these to 

your desired amounts.  Press the channel key to select the channel, and the + and – keys to set the rates.  
I would set up the high rate at 100% and the low rate between 80% and 90%.  Next press the select key 
to get to the expo set up for each channel, and use the + and – keys to set the values.  You can set 
various values for each rate.  Leave these a 0% to start with, and you can come back to these to set them 
as desired after test flying the helicopter.   

Содержание JR 8103 Heli

Страница 1: ... to SWASH TYP This is where you can set the radio for CCPM Press the key one time for 2 servo 180 degree again for 3 servo 120 degree and once more for 4 servo 90 degree If you do not have a CCPM helicopter leave this at 1 servo NORM If it is CCPM choose the type of set up you have Your instructions for the helicopter should have this information listed as to which type it is Then you can press th...

Страница 2: ...performance of the helicopter When properly adjusted together with the throttle curves the main rotor head RPM should remain consistent throughout all maneuvers and throttle stick positions This in turn will also improve the effectiveness and accuracy of the tail rotor and gyro system To adjust the pitch curve in the 8103 press the up key until you get to the screen saying PIT CURV You will press ...

Страница 3: ...ng test flights to achieve a constant main rotor rpm for each flight mode and every maneuver Adjust these values as required and do so in the same way as adjusting the pitch curves Gyro Set Up Most gyros come with good set up directions Follow these when setting up the gyro The helicopter kit will also most likely have some settings for the gyro for that helicopter If you have a gyro that has adju...

Страница 4: ... GEAR Now you will press the select key twice to make the arrow point at SW Press the key until this says F S12 Press the select key 3 times to bring the arrow back to Rate Put your flight mode switch upper left hand short 3 position switch to flight mode 1 or 2 This will be pulling the switch either in the center position or all the way towards you Now you will press the key until the value becom...

Отзывы: