10
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
TREADMILL
OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES
11
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
TREADMILL OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
ASSEMBLY
STEP 2
(CONTINUED)
FLAT WASHER (E)
BOLT (D)
RIGHT CONSOLE MAST
MAIN FRAME
WAVY WASHER (F)
ELEVATION FRAME
CONSOLE CABLE
PRE-ATTACHED BOLT
FOOT LOCK LATCH
RIGHT LINKAGE ARM
PRE-ATTACHED NUT
PRE-ATTACHED
TEFLON WASHER
1
3
2
NOTE:
If you have attempted to
move the treadmill from the box
and the machine has sprung
open and cannot be assembled,
refer to the troubleshooting
section in order to restore the
treadmill to its proper position.
*
Insert 1
BOLT (D)
and 1
FLAT WASHER (E)
through
RIGHT CONSOLE MAST
followed by 1
WAVY WASHER (F)
and attach to
MAIN FRAME.
Unscrew
PRE-ATTACHED NUT
and remove from
RIGHT
LINKAGE ARM
and discard. Carefully move
RIGHT LINKAGE
ARM
and
PRE-ATTACHED TEFLON WASHER
into position
and attach to
ELEVATION FRAME
.
NOTE: While holding
RIGHT CONSOLE MAST
in the
upright position, tighten
PRE-ATTACHED BOLT
using
T-wrench to attach
RIGHT LINKAGE ARM
.
Cut band holding
FOOT LOCK LATCH
assembly. Lift the
RUNNING DECK
until lock latch on side of treadmill is
fully engaged.
Remove
CONSOLE
from box and place out of the way.
Lower the treadmill
RUNNING
DECK
from the folded
position by stepping on
LOCK LATCH
on lower right side.
A
B
C
D
E
HARDWARE BAG 2 CONTENTS:
LOCK LATCH PIN (G)
Qty: 1
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
ASSEMBLY
STEP
FLAT WASHER (B)
CONSOLE MAST
CONSOLE CABLE
SPRING WASHER (I)
BOLT (H)
CONSOLE
DO NOT ATTACH
THIS SIDE UNTIL STEP 3-D
FLAT WASHER (B)
20 mm
Qty: 4
SPRING WASHER (I)
15 mm
Qty: 4
BOLT (H)
20 mm
Qty: 4
HARDWARE BAG CONTENTS :
A
Open
HARDWARE BAG
.
B
With running deck in lowered position, place
CONSOLE
on the console masts. Align the
brackets that are underneath the console with the top holes of the console masts.
C
To assemble the
CONSOLE
to the
LEFT CONSOLE MAST
, insert 1
BOLT (H),
1
SPRING WASHER (I)
and 1
FLAT WASHER (B)
into the 2 holes in the
LEFT CONSOLE MAST
and lightly tighten.
D
Gently lift
RIGHT
side of the
CONSOLE
to connect the
CONSOLE CABLE
. Carefully tuck wire
in mast to avoid damage.
NOTE:
Do not pinch console cable or grip pulse wires.
E
Repeat
STEP C
above to assemble the
RIGHT CONSOLE MAST
to the
CONSOLE
.
F Leave console bolts loose until after STEP is completed.
LS780T_Rev.1.3.indd 10-11
6/2/08 4:40:32 PM
