horiba TPNA-500 Скачать руководство пользователя страница 112

Страница: 112 / 261

Function



WARMUP OUTPUT SET

Specifies the warm-up output.

Operation procedure

Press [DATA OUTPUT SET] in the OUTPUT SET screen.

The DATA OUTPUT screen will be displayed.

Press [WARMUP OUTPUT SET].

The WARMUP OUTPUT screen will be displayed.

Specify the warm-up output.

Item

Setting range

Default

value

Description

Output Mode

Hold

Locks the TP/TN concentration analog output during warm-up to the
previous value.

Preset

Locks the TP/TN concentration analog output during warm-up to the
preset value.

Direct

Outputs the TP/TN concentration analog output during warm-up to
the measurement value.

Preset

0 mA to 22 mA

22 mA

Specifies the preset value for the TP/TN concentration analog output
during warm-up.

Main

SETTING

OUTPUT SET

[MENU]

[OUTPUT SET]

[SETTING]

Refer to “ To display the [MENU] item screen” (page 62).

[DATA

DATA OUTPUT

OUTPUT SET

[WARMUP

Preset

Output

Output Mode

Preset

WARMUP OUTPUT

OUTPUT

SET]

OUTPUT SET]

Mode

[ ]

Содержание TPNA-500






































































































































































































































































Результаты поиска

Содержание TPNA-500

Отзывы:

Бренды по названию

Популярные бренды

horiba TPNA-500, Инструкция по эксплуатации

Результаты поиска

Содержание TPNA-500

Отзывы:

Бренды по названию

Популярные бренды