horiba TPNA-500 Скачать руководство пользователя страница 110

Страница: 110 / 261

Function



ALARM OUTPUT SET

Specifies the alarm output.

Operation procedure

Press [DATA OUTPUT SET] in the OUTPUT SET screen.

The DATA OUTPUT screen will be displayed.

Press [ALARM OUTPUT SET].

The ALARM OUTPUT screen will be displayed.

Specify the alarm output.

Item

Setting range

Default value

Description

Output Mode

Hold

Locks TP/TN concentration analog output during alarm
activation to the previous value.

Preset

Locks TP/TN concentration analog output during alarm
activation to a preset value.

Direct

Outputs the measurement value to the TP/TN
concentration analog output during alarm activation.

Preset

0 mA to 22 mA

22 mA

Specifies the preset value for the TP/TN concentration
analog output during alarm activation.

[MENU]

Main

SETTING

OUTPUT SET

[OUTPUT SET]

[SETTING]

Refer to “ To display the [MENU] item screen” (page 62).

DATA OUTPUT

[DATA

OUTPUT SET

[ALARM

OUTPUT

SET]

OUTPUT

SET]

Output Mode

ALARM OUTPUT

Preset

Output

Preset <Input a value>

Mode

[ ]

Содержание TPNA-500






































































































































































































































































Результаты поиска

Содержание TPNA-500

Отзывы:

Бренды по названию

Популярные бренды

horiba TPNA-500, Инструкция по эксплуатации

Результаты поиска

Содержание TPNA-500

Отзывы:

Бренды по названию

Популярные бренды