background image

For your safety

V

Safety precautions

This section provides precautions for using the product safely and correctly and to
prevent injury and damage. The terms of DANGER, WARNING, and CAUTION indicate
the degree of imminency and hazardous situation. Read the precautions carefully as it
contains important safety messages.

Instrument and electrode

WARNING

Do not use an unspecified AC adapter.
Otherwise, it may heat up or be ignited resulting in a fire or an accident.

Do not disassemble or modify the instrument.
Otherwise, it may heat up or be ignited resulting in a fire or an accident.

CAUTION

Harmful chemicals

The internal solution of DO electrodes is highly potassium hydroxide (KOH). 
If the internal solution comes in contact with the skin, wash it off 
immediately. If it gets into eyes, flush with plenty of water and then consult a 
doctor.

Harmful chemicals

The internal solution of pH electrode is highly concentrated potassium 
chloride (3.33 mol/L KCl). If the internal solution comes in contact with the 
skin, wash it off immediately. If it gets into the eyes, flush with plenty of water 
and then consult a doctor.

Broken glass

Broken glass may cause injury. The outer tube and tip of an electrode are 
made of glass. Handle them with care.

Do not use the RS-232C communication and the AC adapter under wet or 
humid conditions. Otherwise, it may cause a fire, electric shock, or 
breakage.

Содержание LAQUAact-PD110






















































































































Отзывы: