horiba LAQUAact-PD110 страница 3 Скачать руководство пользователя | Manualshive

Страница: 3 / 117

background image

I

Preface

This manual describes the operation of the Handheld pH/ORP/Dissolved Oxygen Meter
LAQUAact-PD110.
Be sure to read this manual before using the product to ensure proper and safe
operation of the product. Also safely store the manual so it is readily available whenever
necessary.
Product specifications and appearance, as well as the contents of this manual are
subject to change without notice.

■

Warranty and responsibility

HORIBA, Ltd. warrants that the Product shall be free from defects in material and
workmanship and agrees to repair or replace free of charge, at option of HORIBA, Ltd.,
any malfunctioned or damaged Product attributable to responsibility of HORIBA, Ltd. for
a period of two (2) year from the delivery unless otherwise agreed with a written
agreement. In any one of the following cases, none of the warranties set forth herein
shall be extended;

・

Any malfunction or damage attributable to improper operation

・

Any malfunction attributable to repair or modification by any person not authorized
by HORIBA, Ltd.

・

Any malfunction or damage attributable to the use in an environment not specified in
this manual

・

Any malfunction or damage attributable to violation of the instructions in this manual
or operations in the manner not specified in this manual

・

Any malfunction or damage attributable to any cause or causes beyond the
reasonable control of HORIBA, Ltd. such as natural disasters

・

Any deterioration in appearance attributable to corrosion, rust, and so on

・

Replacement of consumables

HORIBA, LTD. SHALL NOT BE LIABLE FOR ANY DAMAGES RESULTING FROM ANY
MALFUNCTIONS OF THE PRODUCT, ANY ERASURE OF DATA, OR ANY OTHER
USES OF THE PRODUCT.

■

Trademarks

・

Microsoft, Windows are registered trademarks or trademarks of Microsoft Corporation

in the United States and other countries.

Other company names and brand names are either registered trademarks or trademarks
of the respective companies. (R), (TM) symbols may be omitted in this manual.

CODE:I2005023000



3200635713



GZ0000427800

January, 2016

　　



2016 HORIBA, Ltd.

«
1
2
3
4
5
...
»

Содержание LAQUAact-PD110






















































































































Отзывы:

Нет отзывов

Похожие инструкции для LAQUAact-PD110

Бренд: Lumel Страницы: 32

Бренд: IFR Страницы: 46

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: Qu-Bit Electronix Страницы: 10

Бренд: Zeversolar Страницы: 35

Бренд: Zenner Страницы: 52

Бренд: Alfa Laval Страницы: 18

Бренд: CAS Corporation Страницы: 20

Combo meter P700 Pro

Бренд: AquaMaster Страницы: 20

Бренд: Z-TRAUQ Страницы: 10

ISOLGUARD HIG93

Бренд: hakel Страницы: 15

Бренд: QuantoLux Страницы: 12

Smart Meter TS 5kA-3

Бренд: Fronius Страницы: 44

Бренд: Ruide Страницы: 19

Бренд: TFA Страницы: 68

Бренд: Nokeval Страницы: 14

Бренд: DMQ Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды