manualshive.com logo in svg

horiba LAQUAact-EC110, Инструкция по эксплуатации

Поделиться
Скачать
horiba LAQUAact-EC110 Скачать руководство пользователя страница 94

Troubleshooting

78

●

The indicated value does not change/No response

●

The measured value is outside the display range

When the measured value is below the display range, "Ur" appears. When the measured
value is over the display range, "Or" appears.

●

Repeatability of the measured value is poor

Cause

How to solve problem

The conductivity cell is broken.

Replace the conductivity cell.

The conductivity cell is not 
connected correctly.

Connect the conductivity cell correctly.

The instrument is in HOLD state. Cancel the HOLD state.

Instrument defect

Consult your dealer.

Cause

How to solve problem

Sample is out of the 
measurement range.

Use a sample within the measurement range.

The conductivity cell cable is 
broken.

Replace the conductivity cell.

Cell constant is not set.

Set the cell constant.

Calibration is not performed or 
performed incorrectly.

Perform calibration correctly.

Instrument defect

Check as explained below.

Cause

How to solve problem

Effect of the sample solution

Repeatability becomes poor when the conductivity of the 
sample changes over time.

The conductivity cell is dirty.

Clean the conductivity cell.

The conductivity cell is broken.

Replace the conductivity cell.

Содержание LAQUAact-EC110










































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды