4
ENGLISH
SAFETY PRECAUTIONS
❍
1. Your Edge 540M should not be considered a toy,
but rather a sophisticated, working model that
functions very much like a full-size airplane. Because
of its performance capabilities, the Edge 540M, if not
assembled and operated correctly, could possibly
cause injury to yourself or spectators and damage to
property.
❍
2.You must assemble the model according to the
instructions. Do not alter or modify the model, as
doing so may result in a unsafe or unflyable model.
In a few cases the instructions may differ slightly
from the photos. In those instances the written
instructions should be considered as correct.
❍
3. You must take time to build straight, true and
strong.
❍
4. You must use an R/C radio system that is in first-
class condition and a correctly sized engine and
components (fuel tank, wheels, etc.) throughout the
building process.
❍
5. You must correctly install all R/C and other
components so that the model operates correctly on
the ground and in the air.
❍
6. You must check the operation of the model before
every flight to insure that all equipment is operating
and that the model has remained structurally sound.
Be sure to check clevises or other connectors often
and replace them if they show any signs of wear or
fatigue.
❍
7. If you are not already an experienced R/C pilot,
you should fly the model only with the help of a
competent, experienced R/C pilot.
❍
8. While this kit has been flight tested to exceed
normal use, if the plane will be used for extremly
hight stress flying, such as racing, or if an engine
larger than one in the recommended range is
used, the modeler is responsible for taking steps to
reinforce the hight stress points and/or substituting
hardware more suitable for the increased stress.
❍
9. WARNING: The cowl and wheel pants included in
this kit are made of fiberglass, the fibers of which
may cause eye, skin and respiratory tract irritation.
Never blow into a part to remove fiberglass dust, as
the dust will blow back into your eyes. Always wear
safety goggles, a particle mask and rubber gloves
when grinding, drilling and sanding fiberglass parts.
Vacuum the parts and work area thoroughly after
working with fiberglass parts.
RECOMMENDED ACCESSORIES
This is a partial list of items required to finish the Edge 540-M
that may require planning or decision-making before starting
to build. Order numbers are provided in parentheses.
❍
1 x Motorset FW 5065 order no.: FLWA8007
❍
2 x TACM0225 (Elevator)
❍
3 x TACM0245 (Ailerons and Rudder)
❍
1 x Lipo-Akku 6s 4350mAh 30C order no.: FPWP3436
❍
1 x 6-channel receiver TACL0625
❍
4 x Servo cable extensions
ADDITIONAL ITEMS REQUIRED
HARWARE AND ACCESSORIES
In addition to the items listed in the “Decisions You Must
Make” section, following is the list of hardware and accessories
required to finish the Edge 540-M. Order numbers are provided
in parentheses.
❍
Hook & Loop Velcro (GPMQ4480) or Flitework 300mm
battery belt.
COVERING ACCESSORIES
❍
21st Century® sealing iron (COVR2700)
❍
21st Century trim seal iron (COVR2750)
❍
21st Century iron cover (COVR2702)
ADHESIVES AND BUILDING SUPPLIES
In addition to common household tools and hobby tools, this
is the “short list” of the most important items required to build
the Edge 540-M. Great Planes Pro™ CA and Epoxy glue are
recommended.
❍
1/2 oz. Thin Pro CA (GPMR6001)
❍
1/2 oz. Medium Pro CA+ (GPMR6007)
❍
6-Minute Epoxy (GPMR6045)
❍
30-Minute Epoxy (GPMR6047)
❍
Small T-pins (HCAR5100)
❍
Electric drill
❍
Drill bit set including (1/16" 3/32" 1/8" 5/64" and 1/2" bits)
❍
Small Phillips and flat blade screwdrivers (HCAR1040)
❍
Pliers with wire cutter (HCAR0630)
❍
Standard Hex wrench set (HCAR0520)
Содержание FLW4090
Страница 15: ...15 ENGLISH NOTES ...