Honeywell Youjie HH660 Скачать руководство пользователя страница 64

Страница: 64 / 164

5 - 2

from the

Programming Chart

inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999 is a

universal number, indicating all lengths.)

Step 6. Editor Commands

Refer to

Data Format Editor Commands

(page 5-3). Scan the symbols that represent the command you want to enter.

Step 7.

Scan

Save

to save your data format, or

Discard

to exit without saving your changes.

Other Programming Selections

Clear One Data Format

This deletes one data format for one symbology. If you are clearing the primary format, scan

from the

Programming

Chart

inside the back cover of this manual. If you are clearing an alternate format, scan

, or

, depending on the

format you are clearing. Scan the Terminal Type and Code I.D. (see

Symbology Charts

on page A-1), and the bar code

data length for the specific data format that you want to delete. All other formats remain unaffected.

Clear all Data Formats

This clears all data formats.

Save

to exit and save your data format changes.

Discard

to exit without saving any data format changes.

Enter Data Format

Save

Discard

Clear One Data Format

Clear All Data Formats

Save

Discard

Содержание Youjie HH660





































































































































































Результаты поиска

Содержание Youjie HH660

Отзывы:

Honeywell Youjie HH660, Руководство пользователя, Страница: 64 / 164

Результаты поиска

Содержание Youjie HH660

Отзывы: