Honeywell Youjie HH660 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 164

Honeywell Youjie HH660 Скачать руководство пользователя страница 61

4 - 3

Function Code Transmit

When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function
code to the terminal. Charts of these function codes are provided in

Reference Charts

starting on

. When the scanner

is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted.

Default = Enable.

Intercharacter, Interfunction, and Intermessage Delays

Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage
delays slow the transmission of data, increasing data integrity.

Intercharacter Delay

An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each
character of scanned data. Scan the

Intercharacter Delay

bar code below, then scan the number of 5ms delays, and the

Save

bar code using the

Programming Chart

inside the back cover of this manual.

To remove this delay, scan the

Intercharacter Delay

bar code, then set the number of delays to 0. Scan the

Save

bar code

using the

Programming Chart

inside the back cover of this manual.

Note: Intercharacter delays are not supported in USB serial emulation.

User Specified Intercharacter Delay

An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular
character of scanned data. Scan the

Delay Length

bar code below, then scan the number of 5ms delays, and the

Save

bar code using the

Programming Chart

inside the back cover of this manual.

Clear One Suffix

Clear All Suffixes

* Enable

Disable

1

2

3

4

5

Intercharacter Delay

Prefix

Scanned Data

Suffix

Intercharacter Delay

«
...
59
60
61
62
63
...
»

Содержание Youjie HH660





































































































































































Отзывы:

Нет отзывов