Honeywell WPS Series Скачать руководство пользователя страница 1

m

 WARNING

PERSONAL INJURY

DO NOT USE these products as safety or emergency stop 
devices or in any other application where failure of the product 
could result in personal injury.

Failure to comply with these instructions could result in 
death or serious injury.

Quick Start Guide for the

WPS Series Wireless Pressure Sensor

Sensing and Control

Issue 1

50095585

m

 WARNING

Honeywell does not recommend using devices for critical 
control applications where there is, or may be, a single point of 
failure or where single points of failure may result in an unsafe 
condition. It is up to the end-user to weigh the risks and benefits 
to determine if the products are appropriate for the application 
based on security, safety and performance. Additionally, it is 
up to the end-user to ensure that the control strategy results in 
a safe operating condition if any crucial segment of the control 
solution fails. Honeywell customers assume full responsibility 
for learning and meeting the required Declaration of Conformity, 
Regulations, Guidelines, etc. for each country in their distribution 
market.

m

 WARNING

RF EXPOSURE

To satisfy FCC RF exposure requirements for mobile transmitting 
devices, a separation distance of 20 cm or more should be 
maintained between the antenna of this device and persons 
during device operation To ensure compliance, operation at 
closer than this distance is not recommended. The antenna 
used for this transmission must not be co-located in conjunction 
with any other antenna or transmitter.

Failure to comply with these instructions could result in 
death or serious injury.

m

 WARNING

The WPS must be installed in accordance with the requirements 
specified in this document in order to comply with the specific 
Country Communication Agency requirements (i.e., FCC, IC, 
ETSI, ACMA, etc.). See Section 3 as this requires choosing the 
correct Country Use Code and thus allowable antenna and/or 
cable usage.

Содержание WPS Series


























































Отзывы: