Honeywell W8703A Скачать руководство пользователя страница 1

® U.S. Registered Trademark
Copyright © 2002 Honeywell •                •  All Rights Reserved 

INSTALLATION INSTRUCTIONS

69-1344-1

W8703A

 Damper Interface Module

APPLICATION

The W8703A Damper Interface Module (DIM) controls 

up to three conventional zone dampers when used with 
T8635L Microelectronic Communicating Programmable 

Thermostats and the W8635 Equipment Interface 
Module, Table 1. The W8703A uses Enviracom, a low-

cost wired communications protocol.

Using the W8703A Damper Interface Module with up to 
three T8635L Microelectronic Communicating Program-

mable Thermostats and a W8635A,B Equipment 
Interface Module enables the following features:

• Time synchronization.

• Shared filter indication.

• Outdoor temperature display in all zones with only 

one C7089B Outdoor Temperature Sensor 
connected.

• Vacation Hold in all zones.
• Check LED in all zones (when used with the 

W8635B Equipment Interface Module for heat 
pumps).

• System switch setting automatically changes in all 

zones.

• Individual fan control in each zone.

NOTES:

Up to three T8635 Thermostats can be con-

trolled with the W8703A Damper Interface 
Module. 

Up to six zones can be controlled using two 
W8703A and up to nine zones can be con-

trolled using three W8703A.

Table 1. W8703A Description.

Required Accessories

1.

T8635L Microelectronic Communicating Pro-

grammable Thermostat.

2.

W8635A Equipment Interface Module for up to 

2H/2C conventional applications or W8635B 
Equipment Interface Module for up to 2H/1C heat 

pump applications. 

INSTALLATION

When Installing this Product . . .

1.

Read these instructions carefully. Failure to follow 
them could damage the product or cause a haz-

ardous condition.

2.

Check the ratings given in the instructions and on 

the product to make sure the product is suitable 
for your application.

3.

Installer must be a trained, experienced service 

technician.

4.

After installation is complete, check out product 

operation as provided in these instructions.

5.

Follow local codes for installation and application.

CAUTION

Voltage Hazard.

Can cause electrical shock or equipment 
damage.

Disconnect power before beginning installation.

Location

Locate the W8703A in the equipment room near the 
HVAC equipment. See Fig 1.

Model

Application

Recommended Zone Dampers

Comments

W8703A

Controls up to 
three zone 

dampers.

Trol-A-Temp

 Model AOBD

or

Trol-A-Temp

 Model ARD

or

Trol-A-Temp

 Model ZD

Use with T8635L Microelectronic 
Communicating Programmable 

Thermostat and W8635A,B Equipment 
Interface Modules.

Содержание W8703A













Отзывы: