Honeywell VX3Plus Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 282

Honeywell VX3Plus Скачать руководство пользователя страница 62

Serial Connection

The connection type must be changed to

Serial 1 @ 57600

or

Serial 3 @ 57600

depending on which serial port on the

VX3Plus is used.

To change the connection type select

Start > Settings > Control Panel > PC Connection

Tap the Change button. From the popup list, choose

Serial 1 @ 57600

or

Serial 3 @ 57600

This will set up the mobile device to use the serial port. Tap OK and ensure the check box for “Allow connection with desktop
computer when device is attached” is checked.

Tap OK to return to the Control Panel. If desired, any control panel windows may be closed.

Select

Start > Settings > Scanner

and ensure the integrated scanner is set to a port that is NOT the same as the ActiveSync

port.

Connect the correct cable to the PC (the host) and the mobile device (the client). Select “Connect” from the Start Menu on the
client (

Start > Programs > Communications > Connect

).

Note:

Run “Connect” when the “Get Connected” wizard on the host PC is checking COM ports to establish

a connection for the first time.

Cable for Serial ActiveSync Connection

Serial ActiveSync

9000054CABLE

, RS-232 9 Pin to 9 Pin, VX3Plus Serial port to PC/Laptop serial port

l

Connect one end of the cable to the COM port (labeled RS-232 COM1) on the VX3Plus endcap.

l

Connect the other end to a COM port on a PC or laptop.

3-22

«
...
60
61
62
63
64
...
»

Содержание VX3Plus



























































































































































































































































































Отзывы:

Нет отзывов