Honeywell VX3Plus Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 282

Honeywell VX3Plus Скачать руководство пользователя страница 33

Audio Connector

Note:

When the remote antenna mount is ordered, the VX3Plus does not have an audio connector.

The VX3Plus audio connector accepts a headset with a 2.5mm plug, such as a mono telephone headset with microphone or a
stereo headset.

1. Microphone

2. Speaker

3. Ground

An adapter cable (Part No. 9000056CABLE) can be attached to the audio port. The adapter cable has a 2.5mm plug on one end
to attach to the VX3Plus and a quick disconnect connector on the other end to connect to a variety of voice recognition
headsets.

Please refer to

Start > Settings > Control Panel > Mixer

for information on configuring the audio port for either a mono

headset with microphone or a stereo headset.

Note:

The device is not configured for standard PC speakers.

Power Supply Connector

Power is supplied to the VX3Plus through the power connector. Additionally this assembly provides a connection point for the
vehicle’s chassis ground to be connected internally to the conductive chassis of the computer.

The VX3Plus internal power supply can accept DC input voltages in the range of 12 to 80 Volts DC.

1. DC

Positive
(+)

2. DC

Negative
(-)

3. Chassis

Ground

Antenna Connector (Optional)

VX3Plus’s ordered with an external remote antenna option have an antenna connector located on top of the unit. VX3Plus’s
ordered with the internal antenna option do not have an external antenna connector.

2-13

«
...
31
32
33
34
35
...
»

Содержание VX3Plus



























































































































































































































































































Отзывы:

Нет отзывов