Honeywell Vuquest 3330g Скачать руководство пользователя страница 131

Страница: 131 / 201

7 - 47

Planet Code Check Digit

This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data.

Default

= Don’t Transmit.

Postnet Check Digit

This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data.

Default =

Don’t Transmit.

Australian Post Interpretation

This option controls what interpretation is applied to customer fields in Australian 4-State symbols.

Bar Output

lists the bar patterns in “0123” format.

Numeric N Table

causes that field to be interpreted as numeric data using the N Table.

Alphanumeric C Table

causes the field to be interpreted as alphanumeric data using the C Table. Refer to the Australian

Post Specification Tables.

Planet Code,

Postal-4i,

Intelligent Mail Bar Code, and

Postnet On

Planet Code,

Postal-4i,

Intelligent Mail Bar Code, and

Postnet with B and B’ Fields On

Transmit Check Digit

* Don’t Transmit Check Digit

Transmit Check Digit

* Don’t Transmit Check Digit

Содержание Vuquest 3330g










































































































































































































Результаты поиска

Содержание Vuquest 3330g

Отзывы:

Похожие инструкции для Vuquest 3330g

Бренды по названию

Популярные бренды

Honeywell Vuquest 3330g, Руководство пользователя

Результаты поиска

Содержание Vuquest 3330g

Отзывы:

Похожие инструкции для Vuquest 3330g

Бренды по названию

Популярные бренды