background image

6    

sensing.honeywell.com

MICRO SWITCH VPX Series

ISSUE F

  

 

32312068

Figure 7. Ground Screw Locations

9.  Spare terminal strip positions are available for making 

junction connections for accessories such as pneumatic 
solenoid valves. The terminal strip will accept 0,5 mm

2

 to 4 

mm

2

 [20-16 AWG] wire. Insert the stripped ends of the wire 

to each connection and tighten the screws to 0,4 Nm ±0,1 
Nm [3.5 in-lb ±1 in-lb].

Figure 8. Spare Terminal Block Locations

Spare terminal blocks

10.  For installations utilizing the UL or cUL certifications, 

install conduit plugs in unused openings. For installations 
utilizing the ATEX/IEC Ex certifications, install blanking 
elements rated Ex db IIC Gb IP66 and Ex tb IIIC Db IP66 in 
unused openings. Conduit size is marked on the inside of 
the housing near the conduit openings.  See Figure 6. 

11.  For installation utilizing the UL or cUL certifications, install 

a conduit seal suitable for Class I Groups B, C and D or 
Class II Groups E, F or G within 450 mm [18 inches] of 
every conduit opening. For installations utilizing the ATEX/
IEC Ex certifications, if an Ex conduit sealing device is 
used, it must be installed immediately at each entry. If an 
Ex cable glad is used, it must be installed per the manufac-
turer’s instructions.

12.  It may be desirable to adjust the cams of the product at this 

point to set the switch points. See the adjustment, repair 
and maintenance section for instructions on how to adjust 
the cams.

13.  Reassemble cover, making sure to align the arrows on the 

cover and the base, per Figure 9. Fasten the (4) socket 
head cap screws that fasten the cover to the base using a 
6 mm hex wrench to 18 Nm ±2 Nm [13.3 ft-lb ±1.5 ft-lb]. 
Screw minimum yield strength: 205 MPa. Confirm with a 
shim or “feeler” gauge that the gap between the cover and 
the base does not exceed 0,038 mm [0.0015 in].

CAUTION

Cover joints must be cleaned before replacing the cover. 
Use care when reassembling the cover in order to prevent 
damage to the switch assembly or to the flange surface.

Figure 9. Cover to Base Alignment

Cover fits only one

orientation. Use arrows on

base and cover for alignment

14.  Perform functional tests.
15.  Actuate the VPX switch several times to ensure smooth 

actuation.

IMPORTANT:

 In units with the 90° spring return feature the 

shaft only rotates ±95°. Use care to insure that total travel does 
not exceed 95° in either direction in the application and during 
set-up.

Содержание VPX Series













Отзывы: