Honeywell Voyager 1400g Series Скачать руководство пользователя страница 92

Страница: 92 / 216

6 - 12

NEC 2 of 5

< Default All NEC 2 of 5 Settings >

NEC 2 of 5 On/Off

Check Digit

No Check Digit

indicates that the scanner reads and transmits bar code

data with or without a check digit.

When Check Digit is set to

Validate, but Don’t Transmit

, the unit only

reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit
the check digit with the scanned data.

When Check Digit is set to

Validate and Transmit

, the scanner only reads

NEC 2 of 5 bar codes printed with a check digit, and will transmit this digit
at the end of the scanned data.

Default = No Check Digit.

* On

Off

* No Check Digit

Validate and Transmit

Validate, but Don’t Transmit

Содержание Voyager 1400g Series

























































































































































































































Результаты поиска

Содержание Voyager 1400g Series

Отзывы:

Honeywell Voyager 1400g Series, Руководство пользователя, Страница: 92 / 216

Результаты поиска

Содержание Voyager 1400g Series

Отзывы: