Honeywell Voyager 1400g Series Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 216

Honeywell Voyager 1400g Series Скачать руководство пользователя страница 83

6 - 3

Codabar

<Default All Codabar Settings>

Codabar On/Off

Codabar Start/Stop Characters

Start/Stop characters identify the leading and trailing ends of the bar code.
You may either transmit, or not transmit Start/Stop characters.

Default = Don’t Transmit

.

Codabar Check Character

Codabar check characters are created using different “modulos.” You can
program the scanner to read only Codabar bar codes with Modulo 16 check
characters.

Default = No Check Character.

No Check Character

indicates that the scanner reads and transmits bar

code data with or without a check character.

When Check Character is set to

Validate and Transmit

, the scanner will

only read Codabar bar codes printed with a check character, and will trans-
mit this character at the end of the scanned data.

* On

Off

Transmit

* Don’t Transmit

«
...
81
82
83
84
85
...
»

Содержание Voyager 1400g Series

























































































































































































































Отзывы:

Нет отзывов