manualshive.com logo in svg

Honeywell Voyager 1400g Series, Руководство пользователя, Страница: 150 / 216

Поделиться
Скачать
Honeywell Voyager 1400g Series Скачать руководство пользователя страница 150

8 - 2

Show Data Format

Scan the bar code below to show current data format settings.

Test Menu

When you scan the Test Menu 

On

 code, then scan a programming code in this 

manual, the scanner displays the content of a programming code.  The pro-
gramming function will still occur, but in addition, the content of that program-
ming code is output to the terminal.  

Note: This feature should not be used during normal scanner operation.

EZConfig-Scanning Introduction

EZConfig-Scanning provides a wide range of PC-based programming functions 
that can be performed on a scanner connected to your PC's COM port.  EZCon-
fig-Scanning allows you to download upgrades to the scanner's firmware, 
change programmed parameters, and create and print programming bar codes.  
Using EZConfig-Scanning, you can even save/open the programming parame-
ters for a scanner.  This saved file can be e-mailed or, if required, you can cre-
ate a single bar code that contains all the customized programming parameters 
and mail or fax that bar code to any location.  Users in other locations can scan 
the bar code to load in the customized programming. 

To communicate with a scanner, EZConfig-Scanning requires that the PC have 
at least one available serial communication port, or a serial port emulation using 
a physical USB port.  If you are using the serial port and RS232 cable, an exter-
nal power supply is required.  When using a USB serial port emulation, only a 
USB cable is required.

EZConfig-Scanning Operations

The EZConfig-Scanning software performs the following operations:

Data Format Settings

DFMBK3?.

On

* Off

Содержание Voyager 1400g Series

























































































































































































































Отзывы:

Нет отзывов